✈️FAA Airworthiness Directive
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, -133, - 151N, and -153N airplanes; A320 series airplanes; and A321-211, -212, - 213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, - 253NX, -271NX, and -272NX airplanes. This AD was prompted by a determination that a damage-tolerance and fatigue reassessment of nose landing gear (NLG) repairs is necessary for certain parts fitted on airplanes approved for operation in the Commonwealth of Independent States (CIS). This AD requires repair and replacement of all affected parts, and introduces restrictions for the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More🍼New CPSC Safety Standards for Non-Full-Size Baby Cribs
In December 2010, the U.S. Consumer Product Safety Commission (CPSC or Commission) published a consumer product safety standard for non-full-size baby cribs (NFS cribs) pursuant to section 104 of the Consumer Product Safety Improvement Act of 2008 (CPSIA). The Commission's mandatory standard incorporates by reference ASTM F406, Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/ Play Yards, with modifications that exclude sections of ASTM F406 that apply to play yards exclusively. The CPSIA sets forth a process for updating mandatory standards for durable infant or toddler products that are based on a voluntary standard, when a voluntary standards organization revises the standard. On August 1, 2024, ASTM approved a revised voluntary standard, and this direct final rule updates the mandatory standard for NFS cribs to incorporate by reference the 2024 version of ASTM F406.
Learn More✈️New FAA Airworthiness Directive for GE CF6-80E1A2 and A3 Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This proposed AD was prompted by a manufacturer investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA AD for Piaggio Model P-180 Airplanes Compliance
The FAA proposes to supersede Airworthiness Directive (AD) 2023-25-03, which applies to certain Piaggio Aviation S.p.A. (Piaggio) Model P-180 airplanes. AD 2023-25-03 requires a one-time detailed inspection of the horizontal stabilizer (HS) central box for corrosion; an assessment of the corrosion level; and depending on the determination, repetitive detailed inspections of the HS central box for corrosion and the internal composite structure for surface cracks, distortion, and damage; and repair or replacement of the HS assembly. Repair or replacement of the HS assembly is terminating action for the repetitive inspections. Since the FAA issued AD 2023-25-03, it was determined that AD 2023-25-03 imposed an unintended restriction that is not in the mandatory continuing airworthiness information (MCAI). This proposed AD would retain certain actions of AD-2023-25-03 and would remove the unintended restriction. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🚁FAA Proposes New Airworthiness Directive for Robinson Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2024-19-11, which applies to all Robinson Helicopter Company Model R44 and R44 II helicopters. AD 2024-19-11 requires visually inspecting a certain flex plate assembly (flex plate) and certain clutch shaft forward yokes (yokes), including each flex plate bolt, and depending on the results, taking corrective actions. AD 2024-19-11 also requires removing certain yokes from service within a specified threshold, or as an alternative, performing in-depth inspections. Since the FAA issued AD 2024-19-11, it has been determined that clarifications regarding the alternative inspections are necessary. This proposed AD would retain all the requirements of AD 2024-19-11 and would clarify that the alternative inspections are repetitive and add a particular paint remover option to use when performing those alternative inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Seeks Nominations for Commercial Air Tour Advisory Committee
The FAA is publishing this notice to solicit nominations for membership on the Commercial Air Tour ARC.
Learn More🛡️Updated Safety Standards for Play Yards Effective April 2025
In August 2012, the U.S. Consumer Product Safety Commission (CPSC or Commission) published a consumer product safety standard for play yards pursuant to section 104 of the Consumer Product Safety Improvement Act of 2008 (CPSIA). The Commission's mandatory standard incorporates by reference ASTM F406, Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards, with modifications that exclude sections of ASTM F406 that apply to non- full-size (NFS) cribs exclusively. The CPSIA sets forth a process for updating mandatory standards for durable infant or toddler products that are based on a voluntary standard, when a voluntary standards organization revises the standard. In September 2024, ASTM published a revised voluntary standard, and this direct final rule updates the mandatory standard for play yards to incorporate by reference the 2024 version of ASTM F406.
Learn More📜OSHA Expands Recognition for CSA Group as NRTL Effective January 2025
In this notice, OSHA announces the final decision to expand the scope of recognition for CSA Group & Testing Certification Inc., as a Nationally Recognized Testing Laboratory (NRTL).
Learn More✈️FAA Proposes New Airworthiness Directive Affecting Airbus Aircraft
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, - 132, -133 airplanes. This proposed AD was prompted by a widespread fatigue damage (WFD) scenario review for a certification project that indicated several cracks found around the potable water and wastewater service panels were WFD instead of typical fatigue. This proposed AD would require modification of the potable water and wastewater service panels, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA AD Impacts Costs for GE Engine Compliance
The FAA is revising a notice of proposed rulemaking (NPRM) that applied to all General Electric Company (GE) Model CF34-10E2A1, CF34-10E6, CF34-10E6A1, CF34-10E7, and CF34-10E7-B engines with certain part-numbered high-pressure turbine (HPT) shroud/low pressure turbine (LPT) nozzle assemblies installed. This action revises the NPRM by adding Model CF34-10E5 and CF34-10E5A1 engines to the applicability. The FAA is proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM the agency is requesting comments on this SNPRM.
Learn More