🍼New CPSC Safety Standards for Non-Full-Size Baby Cribs
In December 2010, the U.S. Consumer Product Safety Commission (CPSC or Commission) published a consumer product safety standard for non-full-size baby cribs (NFS cribs) pursuant to section 104 of the Consumer Product Safety Improvement Act of 2008 (CPSIA). The Commission's mandatory standard incorporates by reference ASTM F406, Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/ Play Yards, with modifications that exclude sections of ASTM F406 that apply to play yards exclusively. The CPSIA sets forth a process for updating mandatory standards for durable infant or toddler products that are based on a voluntary standard, when a voluntary standards organization revises the standard. On August 1, 2024, ASTM approved a revised voluntary standard, and this direct final rule updates the mandatory standard for NFS cribs to incorporate by reference the 2024 version of ASTM F406.
Learn More✈️Proposed Airworthiness Directive for Embraer Aircraft by FAA
The FAA proposes to supersede Airworthiness Directive (AD) 2006-20-08, which applies to all Embraer S.A. Model EMB-145, -145ER, - 145MR, -145LR, -145XR, -145MP, and -145EP airplanes. AD 2006-20-08 requires repetitive inspections to detect cracking or failure of the rod ends and fittings of the aileron power control actuator (PCA) and corrective actions if necessary, and provides an optional terminating action. Since the FAA issued AD 2006-20-08, it has been determined that there was an error in identifying a maintenance task number. This proposed AD would continue to require the actions in AD 2006-20-08 and corrects an error in a task number, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive for Rolls-Royce Engines Effective 2025
The FAA is adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent XWB-97 engines. This AD was prompted by a report of damage to the main fuel hose assembly of the fuel manifold, which resulted an in-flight shut down. This AD requires a one-time set of visual and dimensional inspections of the main fuel hose assembly of the fuel manifold to confirm softness, compliance, and lack of resistance, and for shrinkage, cracks, chafing, dents, kinks, necking, and degradation of the hose braid wire; and, if necessary, replacement of the main fuel hose assembly of the fuel manifold, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Aircraft Buckle Compliance
The FAA is superseding Airworthiness Directive (AD) 2021-07-13 for certain Pacific Scientific Company rotary buckle assemblies (buckles). AD 2021-07-13 required inspecting each specified buckle including its buckle handle vane and prohibited installing affected buckles. This AD was prompted by the publication of an updated service bulletin, which revises the applicability based on date of manufacture of the affected buckles. This AD retains certain requirements of AD 2021-07-13, reduces the applicability, and requires performing corrective actions by complying with certain portions of the updated service bulletin. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed AD for Boeing 757
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes. This proposed AD was prompted by a report of cracking found in new locations at a certain body station (STA) during frame segment replacement repairs, including in the web at the K-hole between certain stringers, in the outer chord above the lower hinge intercostal, and in the inner chord and web between certain stringers. This proposed AD would require an inspection or records check for the presence of approved or local repairs, repetitive eddy current inspections for cracking, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🚁FAA Proposes New Airworthiness Directive for Robinson Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2024-19-11, which applies to all Robinson Helicopter Company Model R44 and R44 II helicopters. AD 2024-19-11 requires visually inspecting a certain flex plate assembly (flex plate) and certain clutch shaft forward yokes (yokes), including each flex plate bolt, and depending on the results, taking corrective actions. AD 2024-19-11 also requires removing certain yokes from service within a specified threshold, or as an alternative, performing in-depth inspections. Since the FAA issued AD 2024-19-11, it has been determined that clarifications regarding the alternative inspections are necessary. This proposed AD would retain all the requirements of AD 2024-19-11 and would clarify that the alternative inspections are repetitive and add a particular paint remover option to use when performing those alternative inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Establishes New RNAV Routes Q-162 and Q-166 in Southwest US
This action establishes Area Navigation (RNAV) Routes Q-162 and Q-166 in the southwest United States. The new RNAV routes provide alternative routing for air traffic travelling between southwest Arizona and western Texas in response to severe weather events during the spring and summer months. Additionally, the new RNAV routes expand the availability of RNAV routing in support of transitioning the National Airspace System (NAS) from a ground-based to a satellite-based system for navigation.
Learn More✈️New FAA Airworthiness Directive for GE CF6-80E1A2 and A3 Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This proposed AD was prompted by a manufacturer investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More📈SEC Updates EDGAR Filer Manual
The Securities and Exchange Commission ("Commission") is adopting amendments to Volume II of the Electronic Data Gathering, Analysis, and Retrieval system Filer Manual ("EDGAR Filer Manual" or "Filer Manual") and related rules and forms. EDGAR Release 24.4 will be deployed in the EDGAR system on December 16, 2024.
Learn More✈️Amendment of Class E Airspace for Presque Isle, ME Effective April 2025
This action amends Class E airspace extending upward 700 feet above the surface for Presque Isle International Airport, Presque Isle, ME, by adding and updating airport names in the header and geographic coordinates. This action does not change the airspace boundaries or operating requirements.
Learn More