Trendpublic

🛡️Updated Safety Standards for Play Yards Effective April 2025

In August 2012, the U.S. Consumer Product Safety Commission (CPSC or Commission) published a consumer product safety standard for play yards pursuant to section 104 of the Consumer Product Safety Improvement Act of 2008 (CPSIA). The Commission's mandatory standard incorporates by reference ASTM F406, Standard Consumer Safety Specification for Non-Full-Size Baby Cribs/Play Yards, with modifications that exclude sections of ASTM F406 that apply to non- full-size (NFS) cribs exclusively. The CPSIA sets forth a process for updating mandatory standards for durable infant or toddler products that are based on a voluntary standard, when a voluntary standards organization revises the standard. In September 2024, ASTM published a revised voluntary standard, and this direct final rule updates the mandatory standard for play yards to incorporate by reference the 2024 version of ASTM F406.

✈️FAA Seeks Nominations for Commercial Air Tour Advisory Committee

The FAA is publishing this notice to solicit nominations for membership on the Commercial Air Tour ARC.

📜OSHA Expands Recognition for CSA Group as NRTL Effective January 2025

In this notice, OSHA announces the final decision to expand the scope of recognition for CSA Group & Testing Certification Inc., as a Nationally Recognized Testing Laboratory (NRTL).

✈️FAA Proposes New Airworthiness Directive Affecting Airbus Aircraft

The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, - 132, -133 airplanes. This proposed AD was prompted by a widespread fatigue damage (WFD) scenario review for a certification project that indicated several cracks found around the potable water and wastewater service panels were WFD instead of typical fatigue. This proposed AD would require modification of the potable water and wastewater service panels, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

✈️Proposed FAA AD Impacts Costs for GE Engine Compliance

The FAA is revising a notice of proposed rulemaking (NPRM) that applied to all General Electric Company (GE) Model CF34-10E2A1, CF34-10E6, CF34-10E6A1, CF34-10E7, and CF34-10E7-B engines with certain part-numbered high-pressure turbine (HPT) shroud/low pressure turbine (LPT) nozzle assemblies installed. This action revises the NPRM by adding Model CF34-10E5 and CF34-10E5A1 engines to the applicability. The FAA is proposing this airworthiness directive (AD) to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM the agency is requesting comments on this SNPRM.

⚓Upcoming Public Meeting on Maritime Regulations and Compliance

📋Notice of Information Collection for Occupational Health Forms

✈️FAA Proposes Airworthiness Directive for Airbus A321 Airplanes

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-251NX, -252NX, -253NX, -271NX, and -272NX airplanes. This proposed AD was prompted by discovery of two bushes that had migrated on the latch shaft of an emergency overwing exit door (OWED) during accomplishment of an inspection on an in-service airplane. This proposed AD would require repetitive detailed inspections (DETs) of the affected parts and, in case of discrepancies, modification of the affected parts, and would prohibit the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.

✈️FAA Proposes New Airworthiness Directive for Airbus Helicopters

The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Helicopters Model SA341G and SA342J helicopters. This proposed AD was prompted by reports of corrosion on the contact surfaces of the tail rotor inclined and horizontal drive shaft flanges. This proposed AD would require repetitively inspecting the inclined and horizontal drive shaft flanges and, depending on the results, replacing the inclined or horizontal drive shaft. This proposed AD would also prohibit installing certain inclined and horizontal drive shafts unless certain requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference. The FAA is proposing this AD to address the unsafe condition on these products.

✈️FAA Updates Standard Instrument Approach Procedures Effective 2025

This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.