🚍FTA Withdraws Proposed Rule on Transit Worker Fatigue Management
FTA is withdrawing the October 30, 2023, advance notice of proposed rulemaking (ANPRM) concerning minimum safety standards to address fatigue-related safety incidents. FTA has determined not to issue a notice of proposed rulemaking at this time.
Learn More🚆Updates to Railroad Alcohol and Drug Use Regulations
This rule makes administrative updates to FRA's control of alcohol and drug use regulations, including updating addresses.
Learn More🚂Proposed Rule on Enforcement Discretion by the FRA
This proposed rule would clarify that FRA's Office of the Chief Counsel has discretion to decline or dismiss a violation, such as a technical violation where challenged conduct does not raise a practical safety issue.
Learn More✈️FAA Amendments to Standard Instrument Approach Procedures
This rule establishes, amends, suspends, or removes Standard Instrument Approach Procedures (SIAPS) and associated Takeoff Minimums and Obstacle Departure procedures (ODPs) for operations at certain airports. These regulatory actions are needed because of the adoption of new or revised criteria, or because of changes occurring in the National Airspace System, such as the commissioning of new navigational facilities, adding new obstacles, or changing air traffic requirements. These changes are designed to provide safe and efficient use of the navigable airspace and to promote safe flight operations under instrument flight rules at the affected airports.
Learn More✈️Proposed Airworthiness Directive for Gulfstream Aircraft
The FAA proposes to adopt a new airworthiness directive (AD) for all Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. This proposed AD was prompted by a determination that new and more restrictive airworthiness limitations are necessary. This AD requires revising the maintenance or inspection program, as applicable to incorporate new and more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA Airworthiness Directive for Airbus A350 Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A350-941 and -1041 airplanes. This proposed AD was prompted by reports of electronic centralized aircraft monitor (ECAM) messages requiring flight control remote module (FCRM) replacement linked to solder structural fatigue. This proposed AD would require replacement of affected parts before exceeding the life limit and would limit the installation of affected parts under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Notice of Intent to Designate Abandoned STC for Aviation
This notice announces the FAA's intent to designate Edward L. Soncrant Supplemental Type Certificate (STC) No. SA4289WE as abandoned and make the related engineering data available upon request. The FAA has received a request to provide engineering data concerning this STC. The FAA has been unsuccessful in contacting Edward L. Soncrant concerning the STC. This action is intended to enhance aviation safety.
Learn More🚁FAA Withdraws Proposed Airworthiness Directive for Safran Engines
The FAA is withdrawing an NPRM that proposed to adopt a new airworthiness directive (AD) that would have applied to all Safran Helicopter Engines, S.A. (Safran) Model ARRIUS 2F and ARRIUS 2R engines. The NPRM was prompted by a manufacturer investigation that revealed certain high-pressure (HP) turbine blades may contain non- compliant porosity rates due to a change in the manufacturing process. The NPRM would have required replacement of affected HP turbine blades. Since the NPRM was issued, further investigation and tests demonstrated that the non-compliant rate of porosity has no impact on the use limit of the affected parts and the FAA has determined that the unsafe condition no longer exists. Accordingly, the NPRM is withdrawn.
Learn More✈️Proposed AD for Boeing 787-9 and 787-10
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-9 and 787-10 airplanes. This proposed AD was prompted by reports of multiple supplier notices of escapement (NOEs) indicating that multiple cargo barrier fitting links were possibly manufactured with an incorrect titanium alloy material. This proposed AD would require a high frequency eddy current (HFEC) or handheld X-ray fluorescence (XRF) spectrometer inspection of the cargo barrier fitting link to determine the titanium alloy material, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for CFM Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP- 1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A engines. This proposed AD was prompted by a report of multiple aborted takeoffs and air turn-backs (ATBs) caused by high-pressure compressor (HPC) stall, which was induced by high levels of non-synchronous vibration (NSV). Additional manufacturer investigation revealed that wear on the No. 3 bearing spring finger housing can lead to high levels of NSV. This proposed AD would require initial and repetitive calculations of the levels of NSV, inspection of the stage 2 high- pressure turbine (HPT) nozzle assembly honeycomb and HPT stator stationary seal honeycomb and, depending on the results of the calculations and inspections, replacement of certain parts. This AD also requires replacement of certain No. 3 bearing spring finger housings at a certain time. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More