⚓OSHA Proposes Extension of Info Collection for Marine Terminals
OSHA solicits public comments concerning the proposal to extend the Office of Management and Budget's (OMB) approval of the information collection requirements specified in the Marine Terminals and Longshoring Standard.
Learn More✈️New Airworthiness Directives for Airbus SAS
The FAA is superseding Airworthiness Directive (AD) 2016-20- 12, AD 2018-17-21, and AD 2019-14-04, which applied to certain Airbus SAS Model A318, A319, A320, and A321 series airplanes. AD 2019-14-04 required revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations and terminated the provisions of AD 2018-17-21, which, in turn, terminated the provisions of AD 2016-20-12. This AD was prompted by the determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More🚗NHTSA Notice on Reporting Potential Vehicle Defects
In compliance with the Paperwork Reduction Act of 1995 (PRA), this notice announces that the Information Collection Request (ICR) summarized below will be submitted to the Office of Management and Budget (OMB) for review and approval. The ICR describes the nature of the information collection and its expected burden. This is an extension without change of a currently approved information collection on the reporting of information and documents about potential defects, "Reporting of Information And Communications About Potential Defects".
Learn More✈️New Airworthiness Directive for ATR Airplanes by FAA
The FAA is adopting a new airworthiness directive (AD) for certain ATR--GIE Avions de Transport R[eacute]gional Model ATR42 and ATR72 airplanes. This AD was prompted by a report that a flight deck emergency escape hatch was difficult to open due to the hose ends being connected to the hatch with incorrect parts and/or installed collars with a too- small diameter that would not permit the drain hose to slide inside. This AD requires inspection of the flight deck emergency escape hatch drain hose for discrepancies and applicable corrective actions, and prohibits accomplishment of maintenance actions using the instructions of certain maintenance tasks, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for Airbus SAS A321 Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-111, -112, -131, -211, -212, -213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, -253NX, - 271NX, and -272NX airplanes. This proposed AD was prompted by the identification of an erroneous value of the main landing gear (MLG) tire width in the aircraft data files used for aircraft performance computation. This proposed AD would require revising the existing airplane flight manual (AFM) to incorporate a complementary performance data file (CPDF) update as specified in a European Union Aviation Safety Agency (EASA), which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Special Conditions for Airbus A321neo Seating Safety Regulations
These special conditions are issued for the Airbus Model A321neo ACF and A321neo XLR airplanes. These airplanes will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is a single-occupant oblique seat with an airbag and 3-point or pretensioner restraint system positioned at a 49-degree angle from the cabin centerline. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Learn More✈️FAA Seeks Comments on Fractional Aircraft Ownership Programs Compliance
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request Office of Management and Budget (OMB) approval to renew an information collection. Fractional Ownership is a program that offers increased flexibility in aircraft ownership. Owners purchase shares of an aircraft and agree to share their aircraft with others having an ownership share in that same aircraft. Owners agree to put their aircraft into a "pool" of other shared aircraft and to lease their aircraft to another owner in that pool. This collection is necessary to ensure compliance with relevant safety regulations.
Learn More⚠️DOL Notice on Blasting Operations & OSHA Information Collection
The Department of Labor (DOL) is submitting this Occupational Safety & Health Administration (OSHA)-sponsored information collection request (ICR) to the Office of Management and Budget (OMB) for review and approval in accordance with the Paperwork Reduction Act of 1995 (PRA). Public comments on the ICR are invited.
Learn More🚍Grant of Temporary Exemption for Motorcoach Seat Belt Requirements
In accordance with our regulations, NHTSA is granting a petition from Legacy Limousines and Luxury Coaches for a temporary exemption from the requirement to install Type 2 seat belts (i.e., shoulder belts) at side-facing locations in the company's motorcoaches. The petitioner is a final-stage manufacturer of entertainer-type motorcoaches, seeking temporary exemption from the shoulder belt requirement of Federal Motor Vehicle Safety Standard (FMVSS) No. 208, "Occupant crash protection," for side-facing seats on motorcoaches. The granted exemption permits the petitioner to install Type 1 seat belts (lap belt only) at side-facing seating positions, instead of the Type 2 seat belts (lap and shoulder belts) required by FMVSS No. 208. After reviewing the petition and the comments received, the agency has determined that the requested exemption is warranted to enable the petitioner to sell a vehicle whose overall level of safety or impact protection is at least equal to that of a nonexempted vehicle.
Learn More🚛FMCSA Renews Exemption for Camera Systems in Commercial Vehicles
FMCSA announces its final decision to renew the exemption granted to Vision Systems North America, Inc. (VSNA) to allow motor carriers to operate commercial motor vehicles (CMV) with the company's Smart-Vision high-definition camera monitoring system (Smart-Vision) installed as an alternative to the two rear-vision mirrors required by the Federal Motor Carrier Safety Regulations (FMCSRs).
Learn More