✈️FAA Proposes New Airworthiness Directive for Boeing Aircraft
The FAA proposes to supersede Airworthiness Directive (AD) 2013-08-11, which applies to certain The Boeing Company Model 737-900 and -900ER series airplanes. AD 2013-08-11 requires repetitive inspections for cracking of the fuselage skin along chem-mill steps at certain crown skin and shear wrinkle areas and repair if necessary. Since the FAA issued AD 2013-08-11, the FAA has determined that the compliance times are not adequate. This proposed AD would continue to require the actions in AD 2013-08-11 but at reduced compliance times and would require post-modification inspections if an optional modification is accomplished. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Special Conditions for Boeing 747-8 Safety Standards
These special conditions are issued for the The Boeing Company (Boeing) Model 747-8 series airplane. This airplane, as modified by Boeing, will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is the installation of stairs for flightcrew to access the forward and aft lower lobe compartments during flight. These compartments will have two main functions: storage of service items and that of a Class C cargo compartment. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Learn More✈️New Airworthiness Directive Proposed for Boeing 787 Models
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This proposed AD was prompted by a report of multiple instances of loss of transponder for airplanes entering airspace in the presence of continuous wave (CW) interference, where the transponder did not meet the minimum operational performance standards (MOPS) requirement for transponder response. This proposed AD would require replacing the left and right integrated surveillance system processor unit (ISSPU) hardware. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive Update for Boeing 787 Series Aircraft
The FAA is correcting an airworthiness directive (AD) that was published in the Federal Register. The AD applies to certain The Boeing Company Model 787-9 and 787-10 airplanes. As published, a reference to the Alternative Methods of Compliance (AMOCs) paragraph in the regulatory text is incorrect. This document corrects that error. In all other respects, the original document remains the same.
Learn More✈️New Airworthiness Directive for Boeing 757-200/-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes. This AD was prompted by a report of cracking found in new locations at a certain body station (STA) during frame segment replacement repairs, including in the web at the K-hole between certain stringers, in the outer chord above the lower hinge intercostal, and in the inner chord and web between certain stringers. This AD requires an inspection or records check for the presence of approved or local repairs, repetitive eddy current inspections for cracking, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Boeing 787 Impacts Compliance Costs
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by reports of multiple supplier notices of escapement (NOEs) indicating that seat track splice fittings were possibly manufactured with an incorrect titanium alloy material. This AD requires an inspection of seat track splice fittings to determine the material and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive Proposed for Boeing 737-600 Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2013-08-08, which applies to certain The Boeing Company Model 737-600 series airplanes. AD 2013-08-08 requires repetitive inspections for cracking of the fuselage skin at certain locations at chem-mill steps, and repair if necessary. AD 2013-08-08 also provides optional terminating action for the repetitive inspections. Since the FAA issued AD 2013-08-08, Boeing has reported that the compliance times are not adequate because new fleet data indicates that crack growth is faster and more distributed between tear straps, resulting in longer cracks than originally observed in the test data that prompted AD 2013-08-08. This proposed AD would continue to require the actions in AD 2013-08- 08, at reduced initial compliance times and repetitive intervals for the inspections, and mandate post-modification inspections if the optional modification is accomplished. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Boeing 787 Aircraft
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-9 and 787-10 airplanes. This AD was prompted by reports that some floor beam side-of-body fittings have been manufactured with an incorrect material type. This AD requires replacing the incorrectly manufactured floor beam side-of-body fittings, inspecting the fuselage frame and fastener holes for damage, and repairing any damage. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Safety Standards for Boeing 777-9 by FAA
These special conditions are issued for the Boeing Company (Boeing) Model 777-9 series airplane. This airplane will have a novel or unusual design feature when compared to the state of technology envisioned in the airworthiness standards for transport category airplanes. This design feature is electrical and electronic systems that perform critical functions, the loss of which could be catastrophic to the airplane. The applicable airworthiness regulations do not contain adequate or appropriate safety standards for this design feature. These special conditions contain the additional safety standards that the Administrator considers necessary to establish a level of safety equivalent to that established by the existing airworthiness standards.
Learn More✈️Proposed AD on Boeing 787 Requires Inspections and Replacements
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-9 and 787-10 airplanes. This proposed AD was prompted by reports of multiple supplier notices of escapement (NOEs) documenting pressure deck splice fittings that were possibly manufactured with an incorrect titanium alloy material. This proposed AD would require an inspection of the attach fittings and upper splice fitting of the stub beam horizontal pressure deck (HPD) to determine the type of titanium alloy material, and applicable on- condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More