✈️New Airworthiness Directives for Pratt & Whitney Engines
The FAA is adopting a new airworthiness directive (AD) for certain Pratt & Whitney (PW) Model PW1519G, PW1521G, PW1521GA, PW1521G- 3, PW1524G, PW1524G-3, PW1525G, PW1525G-3, PW1919G, PW1921G, PW1922G, PW1923G, and PW1923G-A engines with a certain high-pressure compressor (HPC) 7th-stage axial rotor installed. This AD was prompted by an analysis of an event involving an International Aero Engines, LLC (IAE LLC) Model PW1127GA-JM engine, which experienced an HPC 7th-stage integrally bladed rotor (IBR-7) separation that resulted in an aborted takeoff. This AD requires performing initial and repetitive angled ultrasonic inspections (AUSI) of certain HPC 7th-stage axial rotors for cracks and replacing the HPC 7th-stage axial rotors if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directives for Boeing 737 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 737-600, -700, -700C, -800, -900, and -900ER series airplanes. This AD was prompted by two engine fan blade-out (FBO) events that resulted in the separation of engine inlet cowl and fan cowl parts from the airplane. In one event, fan cowl parts damaged the fuselage, which caused loss of pressurization and subsequent emergency descent. This AD requires replacing specified inlet cowl aft bulkhead fasteners for certain airplanes; for certain other airplanes, inspecting the inlet cowl aft bulkhead fastener and replacing the fasteners if rivets are found, and, for all airplanes, replacement of the crushable spacers used in the attachment of the inlet cowl to the engine fan case; or as an option, installing a serviceable inlet cowl. This AD also requires revising the existing maintenance or inspection program, as applicable, to incorporate new airworthiness limitations (AWLs). The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directives for CFM Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1A, LEAP-1B, and LEAP- 1C engines. This AD was prompted by a manufacturer investigation that revealed a quality escape for low-pressure turbine (LPT) disks made from forgings with nonconforming grain size. This AD requires removal and replacement of the LPT stage 4 and stage 5 disks. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Amendment of Class E Airspace in Austin and Surrounding Areas
This action corrects a typographic error in the final rule published in the Federal Register on February 24, 2025, amending the Class E airspace at Austin, TX, and establishing Class E airspace at Austin, Lago Vista, and Lakeway, TX.
Learn More🚁Establishment of Class E Airspace for ECU Health Bertie Hospital
This action establishes Class E airspace extending upward from 700 feet above the surface for ECU Health Bertie Hospital Heliport, Windsor, NC, to accommodate new area navigation (RNAV) global positioning system (GPS) standard instrument approach procedures serving the heliport. Controlled airspace is necessary for the safety and management of instrument flight rules (IFR) operations at this heliport.
Learn More✈️Proposed Airworthiness Directive for Airbus Canada Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus Canada Limited Partnership Model BD-500-1A10 and BD-500- 1A11 airplanes. This proposed AD was prompted by events where the cargo bottle fail caution message was displayed. This proposed AD would require replacing affected low rate discharge (LRD) bottles, inspecting extinguishing discharge lines and tubes, and replacing extinguishing discharge lines and tubes, as applicable, and would also prohibit the installation of affected LRD bottles, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🏢Notice of Intent to Release Surplus Property at Melbourne Airport
Notice is being given that the FAA is considering a request from the City of Melbourne to release 55.8 (+/-) acres at the Melbourne Orlando International Airport, Melbourne, FL from the conditions, reservations, and restrictions as contained in a Quitclaim Deed agreement between the FAA and the City of Melbourne, dated April 20, 1948. The release of property will allow the City of Melbourne to dispose of the property for non-aeronautical purposes.
Learn More✈️FAA Issues Airworthiness Directive for Airbus A330 Maintenance
The FAA is superseding Airworthiness Directive (AD) 2023-11- 08, which applied to all Airbus SAS Model A330-841 and -941 airplanes. AD 2023-11-08 required maintenance actions, including a high-pressure valve (HPV) seal integrity test, repetitive replacement of the HPV clips, revision of the existing airplane flight manual (AFM), and implementation of updates to the FAA-approved operator's minimum equipment list (MEL). This AD was prompted by the determination that the replacement intervals required by AD 2023-11-08 must be reduced to address the unsafe condition. This AD continues to require the actions in AD 2023-11-08. This AD also reduces the HPV clip replacement intervals, requires an additional revision of the existing AFM for certain airplanes, and limits the installation of HPV clips, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive for ATR Airplanes Requiring Probe Replacement
The FAA is adopting a new airworthiness directive (AD) for all ATR--GIE Avions de Transport R[eacute]gional Model ATR42 and Model ATR72 airplanes. This AD was prompted by the insufficient accuracy of a certain Angle of Attack (AoA) probe at low airspeeds which could lead to a delayed activation of the stick pusher in a flaps-extended configuration. This AD requires replacing each affected part with a serviceable part, and also prohibits the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive for ATR72 Airplanes by FAA
The FAA is adopting a new airworthiness directive (AD) for all ATR--GIE Avions de Transport R[eacute]gional Model ATR72 airplanes. This AD was prompted by reports of the main landing gear (MLG) rear hinge pin being ruptured. This AD requires replacing affected parts and prohibits the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Learn More