✈️Proposed Airworthiness Directive for Bombardier Aircraft Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This proposed AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Airbus Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and - 233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by a full-scale fatigue test that found cracks on the main landing gear (MLG) bay rear skin panel at the stringer run-out at Frame 46 and Stringer 32 on the left-hand and right-hand sides. This AD requires repetitive special detailed inspections (SDIs) of the affected area for cracking and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New FAA Airworthiness Directive for Airbus SAS Oxygen Generators
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, C4-605R Variant F, F4-605R, and F4-622R airplanes; Model A310 series airplanes; Model A318, A319, A320, and A321 series airplanes; Model A330-200, -200 Freighter, and -300 series airplanes; Model A330-841 and -941 airplanes; and Model A340-211, -212, -213, -311, -312, -313, -541, and -642 airplanes. This AD was prompted by chemical oxygen generators that failed to activate in service and during maintenance activities. This AD requires replacing affected oxygen generators and prohibits the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Airbus SAS Airplanes by FAA
The FAA is superseding Airworthiness Directive (AD) 2022-11- 01, which applied to certain Airbus SAS Model A300 series airplanes; Model A300 B4-600, B4-600R, and F4-600R series airplanes; and Model A300 C4-605R Variant F airplanes (collectively called Model A300-600 series airplanes). AD 2022-11-01 required a detailed inspection (DET) of the main landing gear (MLG) support rib 5 lower flange, a fluorescent penetrant inspection (FPI) around the spot facing of certain fastener holes if necessary, and applicable corrective actions. This AD was prompted by the determination that additional airplanes are affected by the unsafe condition. This AD continues to require the actions in AD 2022-11-01 and adds airplanes to the applicability, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Embraer Airplanes
The FAA is adopting a new airworthiness directive (AD) for all Embraer S.A. Model EMB-135ER, -135KE, -135KL, and -135LR airplanes; and Model EMB-145, -145EP, -145ER, -145LR, -145MP, -145MR, and -145XR airplanes. This AD was prompted by a structural assessment that indicated certain central fuselage longitudinal splices are subjected to fatigue damage on multiple sites due to loose fasteners, which may reduce the structural residual strength below the required levels. This AD requires performing repetitive inspections of certain upper central fuselage longitudinal splices and reporting the inspection results, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is incorporated by reference. This AD also requires performing corrective actions if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues New Airworthiness Directive for Airbus SAS Airplanes
The FAA is superseding Airworthiness Directive (AD) 2022-16- 06, which applied to certain Airbus SAS Model A330-200, A330-200 Freighter, A330-300, and A330-900 series airplanes; and all Model A340- 200 and A340-300 series airplanes. AD 2022-16-06 required modifying the trimmable horizontal stabilizer actuator (THSA) installation, implementing the electrical load sensing device (ELSD) wiring provisions, and installing and activating the ELSD. This AD was prompted by tests that demonstrated that when the upper secondary load path (SLP) of the THSA is engaged, the THSA might not stall, with consequently no indication of SLP engagement, and by the recent determination that the required actions of AD 2022-16-06 cannot be accomplished on certain airplanes. This AD continues to require the actions in AD 2022-16-06 with revised procedures, and also requires additional actions for certain airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for Embraer Aircraft by FAA
The FAA proposes to supersede Airworthiness Directive (AD) 2006-20-08, which applies to all Embraer S.A. Model EMB-145, -145ER, - 145MR, -145LR, -145XR, -145MP, and -145EP airplanes. AD 2006-20-08 requires repetitive inspections to detect cracking or failure of the rod ends and fittings of the aileron power control actuator (PCA) and corrective actions if necessary, and provides an optional terminating action. Since the FAA issued AD 2006-20-08, it has been determined that there was an error in identifying a maintenance task number. This proposed AD would continue to require the actions in AD 2006-20-08 and corrects an error in a task number, as specified in an Ag[ecirc]ncia Nacional de Avia[ccedil][atilde]o Civil (ANAC) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed AD for Boeing 757
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes. This proposed AD was prompted by a report of cracking found in new locations at a certain body station (STA) during frame segment replacement repairs, including in the web at the K-hole between certain stringers, in the outer chord above the lower hinge intercostal, and in the inner chord and web between certain stringers. This proposed AD would require an inspection or records check for the presence of approved or local repairs, repetitive eddy current inspections for cracking, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Aircraft Buckle Compliance
The FAA is superseding Airworthiness Directive (AD) 2021-07-13 for certain Pacific Scientific Company rotary buckle assemblies (buckles). AD 2021-07-13 required inspecting each specified buckle including its buckle handle vane and prohibited installing affected buckles. This AD was prompted by the publication of an updated service bulletin, which revises the applicability based on date of manufacture of the affected buckles. This AD retains certain requirements of AD 2021-07-13, reduces the applicability, and requires performing corrective actions by complying with certain portions of the updated service bulletin. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive for Rolls-Royce Engines Effective 2025
The FAA is adopting a new airworthiness directive (AD) for certain Rolls-Royce Deutschland Ltd & Co KG (RRD) Model Trent XWB-97 engines. This AD was prompted by a report of damage to the main fuel hose assembly of the fuel manifold, which resulted an in-flight shut down. This AD requires a one-time set of visual and dimensional inspections of the main fuel hose assembly of the fuel manifold to confirm softness, compliance, and lack of resistance, and for shrinkage, cracks, chafing, dents, kinks, necking, and degradation of the hose braid wire; and, if necessary, replacement of the main fuel hose assembly of the fuel manifold, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More