✈️New Airworthiness Directive Impacting Boeing 747 Aircraft Operators
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 747-400, 747-400F, 747-8F, and 747-8 series airplanes. This AD was prompted by a report that, during potable water servicing, there were multiple engine indicating and crew alerting system messages. The cause was the separation of a fitting and steel water supply tube above an electronics equipment cooling air filter, behind the forward cargo compartment left sidewall. This AD requires, depending on configuration, installing at certain locations: conduits on exposed potable water supply lines, envelope assemblies over all exposed potable water line fittings and exposed potable water supply lines, a slitted spray shield, a two-piece deflector shield around the equipment cooling system (ECS) air inlet, and/or a shroud on exposed potable water supply lines. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directive for Airbus Duct Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD- 500-1A11 airplanes. This proposed AD was prompted by certification testing that found that environmental control system (ECS) ducts manufactured using a certain material failed the flammability test requirements established for compliance. This proposed AD would require inspecting the affected ECS ducts and, as applicable, installing a fire-resistant sleeve assembly over any non-compliant ECS duct, and prohibit the installation of ECS ducts as replacement parts under certain conditions, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive Mandates Rudder Replacement
The FAA is adopting a new airworthiness directive (AD) for certain FS 2001 Corp, FS 2002 Corporation, FS 2003 Corporation, Piper, and Piper Aircraft, Inc. (Piper) airplanes. This AD was prompted by reports of broken rudders. This AD requires replacing any rudder equipped with a rudder post made from a certain carbon steel with a rudder equipped with a rudder post made from a certain low-alloy steel. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes New Airworthiness Directives for ATR Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2023-10-08, which applies to all ATR--GIE Avions de Transport R[eacute]gional Model ATR42-200, ATR42-300, and ATR42-320 airplanes. AD 2023-10-08 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2023-10-08, the FAA has determined that new or more restrictive airworthiness limitations are necessary. This proposed AD would continue to require certain actions in AD 2023-10-08 and would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA Airworthiness Directive for Airbus A330 Models
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus SAS Model A330-200, A330-200 Freighter, A330-300, A330-800, and A330-900 series airplanes. This proposed AD was prompted by an incorrect shot peening application being implemented in production starting from 2008. This proposed AD would require repetitive detailed inspections (DET) of certain splice fittings and, depending on findings, repair, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directives for Airbus Aircraft
The FAA is revising a notice of proposed rulemaking (NPRM) to supersede Airworthiness Directive (AD) 2021-25-14, which applies to all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and -233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This action revises the NPRM by adding a prohibition against accomplishing a repair using certain structural repair manual (SRM) tasks. The FAA is proposing this AD to address the unsafe condition on these products. Since these actions would impose an additional burden over those in the NPRM, the FAA is requesting comments on this SNPRM.
Learn More✈️Airworthiness Directive 2025
The FAA is superseding Airworthiness Directive (AD) 2019-22- 02, which applied to all The Boeing Company Model 747-200B, 747-200C, 747-200F, 747-300, 747-400, 747-400D, 747-400F, 747-8F, and 747-8 series airplanes. AD 2019-22-02 required identifying the part number, and the serial number if applicable, of the Captain's and First Officer's seats, and applicable on-condition actions for affected seats. AD 2019-22-02 also required a one-time detailed inspection and repetitive checks of the horizontal movement system (HMS) of the Captain's and First Officer's seats, and applicable on-condition actions. This AD was prompted by reports of uncommanded fore and aft movement of the Captain's and First Officer's seats. This AD requires the actions in AD 2019-22-02 and adds an inspection of previously omitted part numbers. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for Boeing 757 Compliance Requirements
The FAA proposes to supersede Airworthiness Directive (AD) 2019-12-13, which applies to all The Boeing Company Model 757 airplanes. AD 2019-12-13 requires repetitive checks of the aileron trim actuator bearing for free rotation, repetitive detailed inspections of the aileron trim actuator attachment lug for damage and cracking, and applicable on-condition actions. Since the FAA issued AD 2019-12-13, the FAA has determined that a modification must be done to address the unsafe condition. This proposed AD would continue to require the actions in AD 2019-12-13. This proposed AD would also require for certain airplanes changing the lateral control box support assembly and installing an aileron trim actuator bracket, and for certain other airplanes replacing the existing actuator lateral control fitting with an aileron trim actuator bracket, which terminates the repetitive checks and inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for DAHER Aerospace TBM 700 Aircraft
The FAA is adopting a new airworthiness directive (AD) for certain DAHER AEROSPACE (DAHER) Model TBM 700 airplanes. This AD was prompted by certain existing emergency procedures in the pilot's operating handbook (POH) that cannot be fully accomplished since certain equipment cannot be disconnected by the pilot(s) from the flight deck. This AD requires revising the existing POH for your airplane to provide the flight crew with corrected emergency procedures. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive for Saab AB Airplanes
The FAA is superseding Airworthiness Directive (AD) 2017-21- 05, which applied to certain Saab AB Model 340A (SAAB/SF340A) and SAAB 340B airplanes. AD 2017-21-05 required revising the existing maintenance or inspection program, as applicable, to incorporate airworthiness limitations, including new inspection tasks for the drag brace support fitting of the main landing gear (MLG) and tasks related to the corrosion prevention and control program (CPCP). This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD continues to require the actions in AD 2017-21-05 and requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference (IBR). The FAA is issuing this AD to address the unsafe condition on these products.
Learn More