✈️FAA Issues Airworthiness Directive for Boeing 757 Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757 airplanes. This AD was prompted by reports of several occurrences of a power transfer unit (PTU) control valve that failed to open when commanded. This AD requires installing new relays and changing certain wire bundles leading to the PTU control valve. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Gulfstream Aircraft Compliance
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. This AD was prompted by a report of cracking in the electrical grounding receptacles located on the left and right wings. This AD requires inspecting the electrical grounding receptacles for cracks and corrosion, performing applicable on-condition actions, and sealing over the grounding receptacles on the top of the wings to permanently disable the receptacle. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Airbus CN-235
The FAA is adopting a new airworthiness directive (AD) for all Airbus Defense and Space S.A. Model CN-235, CN-235-200, and CN-235-300 airplanes. This AD was prompted by a torn bulkhead seal found jamming the nose landing gear (NLG) emergency cable pulley. Due to the similarity of design, the main landing gear (MLG) emergency cable pulley could be exposed to the same failure mode. This AD requires repetitive inspections and corrective actions for damage of affected bulkhead seals and retainer rings, and repetitive replacement of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for General Electric Engines Overview
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, GEnx-2B67, GEnx-2B67B, and GEnx-2B67/P engines. This AD was prompted by a manufacturer evaluation that determined a lower life limit may be necessary for certain stages 6-10 compressor rotor spools than allowed by the engine shop manual (ESM). This AD requires a one- time inspection of the stages 6-10 spools for previously accomplished blend repairs, a one-time inspection of the blend repairs on the stages 6-10 spools for compliance with the updated allowable limits, and replacement if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Regulatory Compliance Costs for Boeing 767 Airworthiness Directive
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -300F airplanes. This AD was prompted by a report of a main landing gear (MLG) collapse event following maintenance where a grinder was operating outside of its input parameters, resulting in possible heat damage to the outer cylinder of the MLG. This AD requires replacing affected outer cylinders. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive for CFM LEAP-1B Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1B engines. This AD was prompted by a report of a quality escape involving certain high- pressure compressor (HPC) stage 2 seals manufactured without detailed finish machining, which could result in deeper rubs and mechanical damage to the seal teeth of the stage 3-4 compressor rotor blisk (stage 3-4 blisk) of the mating compressor rotor during initial operation. This AD requires a visual inspection of the HPC stage 2 seal, a visual inspection of the forward arm seal teeth of the stage 3-4 blisk, an eddy current inspection (ECI) of the forward arm seal teeth of the stage 3-4 blisk, and replacement of the HPC stage 2 seal and the stage 3-4 blisk, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directive for Bombardier Air
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model BD-700-1A10 and BD-700-1A11 airplanes. This proposed AD was prompted by reports of engine-driven pump hydraulic pressure hoses for hydraulic systems number 1 and 2 chafing against the pylon in the aft equipment bay. This proposed AD would require an inspection of the engine-driven pump pressure hoses for any damage and minimum clearance between the engine-driven pump hydraulic pressure hose and case drain, suction pressure hose, and surrounding pylon structure; and corrective actions if necessary. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Class E Airspace Established at Redfield, SD by FAA
This action establishes Class E airspace at Redfield, SD. This action due to the development of new public instrument procedures and to support instrument flight rule (IFR) operations.
Learn More🚁FAA Airworthiness Directive for Airbus H160-B Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model H160-B helicopters. This AD was prompted by a report of excessive axial play of the rotating scissors spherical bearings. This AD requires measuring the axial play of the rotating scissors spherical bearings and, depending on the results, accomplishing corrective action and reporting inspection results, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New FAA Airworthiness Directive for Leonardo Helicopters Compliance
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB139 and AW139 helicopters. This AD was prompted by reports of broken main landing gear (MLG) shock absorber piston rod eye ends. This AD requires repetitively inspecting the MLG shock absorber piston rod eye ends, reporting the results of the inspection, and, depending on the results, replacing the MLG shock absorber assembly. It also prohibits installing certain MLG shock absorber assemblies unless specific requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More