✈️Boeing Airworthiness Directive
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by a report of operators receiving No. 1 flight compartment windows that may not meet type design requirements for withstanding a bird impact. This AD requires replacing affected No. 1 flight compartment windows and prohibits the installation of affected windows. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Withdraws Proposed Rule on Boeing Airworthiness Directives
The FAA is withdrawing a notice of proposed rulemaking (NPRM) that proposed to supersede Airworthiness Directive (AD) 2023-08-04, which applies to certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. The NPRM was prompted by reports of a loss of water pressure during flight and water leaks that affected multiple pieces of electronic equipment, and by the discovery that some clamshell couplings did not have the required safety strap. The NPRM would have required inspecting all door 1 and door 3 lavatory and galley potable water systems for missing or incorrectly installed clamshell couplings, inspecting all clamshell couplings for the presence and correct installation of safety straps at door 1 and door 3 lavatories and galleys with a potable water system, and performing applicable on- condition actions. The NPRM would have also prohibited the installation of affected parts at inspection locations and removed Model 787-10 airplanes from the applicability. Since issuance of the NPRM, the FAA has determined that the identified service information may not adequately address the unsafe condition on one of the galleys, and Model 787-10 airplanes should be included in the applicability. Accordingly, the NPRM is withdrawn.
Learn More✈️FAA Issues Airworthiness Directive for Bombardier Airplanes
The FAA is superseding Airworthiness Directive (AD) 2021-10- 02, which applied to all Bombardier, Inc., Model BD-700-1A10 and BD- 700-1A11 airplanes. AD 2021-10-02 required repetitive general visual inspections of the left- and right-hand elevator torque tube bearings for any sand, dust, or corrosion; repetitive functional tests of the elevator control system; and replacement of the elevator torque tube bearings if necessary. This AD continues to require certain actions in AD 2021-10-02 and requires revising the existing maintenance or inspection program, as applicable, to incorporate a new airworthiness limitation. This AD was prompted by a determination that a new airworthiness limitation is necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive on Boeing 767
The FAA is superseding Airworthiness Directive (AD) 2019-14- 13, which applies to all The Boeing Company Model 767-200, -300, -300F, and -400ER series airplanes. AD 2019-14-13 required identifying the part number, and the serial number if applicable, of the Captain's and First Officer's seats, and performing applicable on-condition actions for affected seats. AD 2019-14-13 also required a one-time detailed inspection and repetitive checks of the horizontal movement system (HMS) of the Captain's and First Officer's seats, and applicable on- condition actions. AD 2019-14-13 also provided an optional terminating action for the repetitive actions for certain seats. This AD was prompted by reports of uncommanded fore and aft movement of the Captain's and First Officer's seats. This AD retains the actions in AD 2019-14-13 and adds an inspection of previously omitted part numbers. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More🚁FAA Issues Airworthiness Directive for Airbus Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS332L, AS332L1, AS 365 N3, SA-365C1, SA- 365C2, SA-365N, and SA-365N1 helicopters. This AD was prompted by a report that certain rescue hoist cable assemblies may be equipped with a defective ball end. This AD requires inspecting certain rescue hoist cable assemblies and, depending on the results, replacing the rescue hoist cable assembly. This AD also allows installing certain rescue hoist cable assemblies and certain rescue hoists provided its requirements are met. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Airbus Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, and -133 airplanes; Model A320-211, -212, -214, -216, -231, -232, and - 233 airplanes; and Model A321-111, -112, -131, -211, -212, -213, -231, and -232 airplanes. This AD was prompted by a full-scale fatigue test that found cracks on the main landing gear (MLG) bay rear skin panel at the stringer run-out at Frame 46 and Stringer 32 on the left-hand and right-hand sides. This AD requires repetitive special detailed inspections (SDIs) of the affected area for cracking and applicable corrective actions, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New FAA Airworthiness Directive for Airbus SAS Oxygen Generators
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A300 B4-601, B4-603, B4-620, B4-622, B4-605R, B4-622R, C4-605R Variant F, F4-605R, and F4-622R airplanes; Model A310 series airplanes; Model A318, A319, A320, and A321 series airplanes; Model A330-200, -200 Freighter, and -300 series airplanes; Model A330-841 and -941 airplanes; and Model A340-211, -212, -213, -311, -312, -313, -541, and -642 airplanes. This AD was prompted by chemical oxygen generators that failed to activate in service and during maintenance activities. This AD requires replacing affected oxygen generators and prohibits the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A319-111, -112, -113, -114, -115, -131, -132, -133, - 151N, and -153N airplanes; A320 series airplanes; and A321-211, -212, - 213, -231, -232, -251N, -252N, -253N, -271N, -272N, -251NX, -252NX, - 253NX, -271NX, and -272NX airplanes. This AD was prompted by a determination that a damage-tolerance and fatigue reassessment of nose landing gear (NLG) repairs is necessary for certain parts fitted on airplanes approved for operation in the Commonwealth of Independent States (CIS). This AD requires repair and replacement of all affected parts, and introduces restrictions for the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive for Boeing Aircraft
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 767-200, -300, and -400ER series airplanes. This AD was prompted by a report of multiple engine indicating and crew alerting system messages during potable water servicing after the water leaked onto the electronics equipment cooling air filter. This AD requires installation of hoseducts around the left-side section 43 potable water supply hoses and connections, a potable water system leakage test, and applicable corrective actions. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directives Impacting Airbus Operators and Costs
The FAA is superseding Airworthiness Directive (AD) 2023-09- 01, which applied to all Airbus SAS Model A318 series airplanes; Model A319 series airplanes; Model A320-211, -212, -214, -216, -231, -232, - 233, -251N, -252N, -253N, -271N, -272N, and -273N airplanes; and Model A321 series airplanes. AD 2023-09-01 was prompted by a report that certain overheat detection system (OHDS) sensing elements installed at certain positions might not properly detect thermal bleed leak events due to a quality escape during the manufacturing process. AD 2023-09-01 required a one-time detailed inspection of each affected part installed at an affected position and replacement if necessary and prohibited the installation of affected parts at affected positions. Since the FAA issued AD 2023-09-01, a new airplane model (A321-253NY) has been certified by EASA, on which affected parts could be installed in service. This AD continues to require the actions in AD 2023-09-01, and revises the applicability to include Model A321-253NY airplanes, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More