🚁FAA Proposes New Airworthiness Directive for Robinson Helicopters
The FAA proposes to supersede Airworthiness Directive (AD) 2024-19-11, which applies to all Robinson Helicopter Company Model R44 and R44 II helicopters. AD 2024-19-11 requires visually inspecting a certain flex plate assembly (flex plate) and certain clutch shaft forward yokes (yokes), including each flex plate bolt, and depending on the results, taking corrective actions. AD 2024-19-11 also requires removing certain yokes from service within a specified threshold, or as an alternative, performing in-depth inspections. Since the FAA issued AD 2024-19-11, it has been determined that clarifications regarding the alternative inspections are necessary. This proposed AD would retain all the requirements of AD 2024-19-11 and would clarify that the alternative inspections are repetitive and add a particular paint remover option to use when performing those alternative inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️New FAA Airworthiness Directive for GE CF6-80E1A2 and A3 Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain General Electric Company (GE) Model CF6-80E1A2, CF6-80E1A3, CF6-80E1A4, and CF6-80E1A4/B engines. This proposed AD was prompted by a manufacturer investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This proposed AD would require replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directive for Airbus A321 Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Airbus SAS Model A321-251NX, -252NX, -253NX, -271NX, and -272NX airplanes. This proposed AD was prompted by discovery of two bushes that had migrated on the latch shaft of an emergency overwing exit door (OWED) during accomplishment of an inspection on an in-service airplane. This proposed AD would require repetitive detailed inspections (DETs) of the affected parts and, in case of discrepancies, modification of the affected parts, and would prohibit the installation of affected parts, as specified in a European Union Aviation Safety Agency (EASA) AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed AD for Boeing 757 Video Monitor Compliance Costs
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 757-200 and -300 series airplanes. This proposed AD was prompted by a report that some passenger service unit (PSU)-mounted video monitors became detached from the PSU rails during a hard landing. This proposed AD would require replacing PSU- mounted video monitors that do not have secondary retention lanyards. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA Airworthiness Directive for Boeing 737 Video Monitors
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 737-600, -700, -700C, -800, -900, and 900ER series airplanes. This proposed AD was prompted by a report that some passenger service unit (PSU)-mounted video monitors became detached from the PSU rails during a hard landing. This proposed AD would require replacing PSU-mounted video monitors that do not have secondary retention lanyards. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🚁Proposed FAA Airworthiness Directive for Siam Hiller Helicopters
The FAA proposes to adopt a new airworthiness directive (AD) for Siam Hiller Holdings, Inc. (Siam Hiller), Model UH-12E (Army OH-23G and H-23F) and UH-12E-L helicopters. This proposed AD was prompted by reports of cracks found in a main rotor (M/R) transmission drive shaft (drive shaft). This proposed AD would require inspecting certain M/R drive shafts for a crack, prohibit installing certain M/R drive shafts unless the inspection is done, and prohibit using certain paint removers. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Airworthiness Directive for CFM LEAP-1B Engines
The FAA is adopting a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1B engines. This AD was prompted by a report of a quality escape involving certain high- pressure compressor (HPC) stage 2 seals manufactured without detailed finish machining, which could result in deeper rubs and mechanical damage to the seal teeth of the stage 3-4 compressor rotor blisk (stage 3-4 blisk) of the mating compressor rotor during initial operation. This AD requires a visual inspection of the HPC stage 2 seal, a visual inspection of the forward arm seal teeth of the stage 3-4 blisk, an eddy current inspection (ECI) of the forward arm seal teeth of the stage 3-4 blisk, and replacement of the HPC stage 2 seal and the stage 3-4 blisk, if necessary. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Gulfstream Aircraft Compliance
The FAA is adopting a new airworthiness directive (AD) for certain Gulfstream Aerospace Corporation Model GVII-G500 and GVII-G600 airplanes. This AD was prompted by a report of cracking in the electrical grounding receptacles located on the left and right wings. This AD requires inspecting the electrical grounding receptacles for cracks and corrosion, performing applicable on-condition actions, and sealing over the grounding receptacles on the top of the wings to permanently disable the receptacle. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Regulatory Compliance Costs for Boeing 767 Airworthiness Directive
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model 767-200, -300, and -300F airplanes. This AD was prompted by a report of a main landing gear (MLG) collapse event following maintenance where a grinder was operating outside of its input parameters, resulting in possible heat damage to the outer cylinder of the MLG. This AD requires replacing affected outer cylinders. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New FAA Airworthiness Directive for Leonardo Helicopters Compliance
The FAA is adopting a new airworthiness directive (AD) for all Leonardo S.p.a. Model AB139 and AW139 helicopters. This AD was prompted by reports of broken main landing gear (MLG) shock absorber piston rod eye ends. This AD requires repetitively inspecting the MLG shock absorber piston rod eye ends, reporting the results of the inspection, and, depending on the results, replacing the MLG shock absorber assembly. It also prohibits installing certain MLG shock absorber assemblies unless specific requirements are met, as specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More