🚁Proposed Airworthiness Directive on Airbus Helicopters Inspections
The FAA proposes to supersede Airworthiness Directive (AD) 2021-26-07, which applies to all Airbus Helicopters Model EC120B helicopters. AD 2021-26-07 requires performing repetitive inspections of the tail rotor (TR) hub body and, depending on the inspection results, replacing certain parts, and accomplishing further inspections. AD 2021-26-07 also requires for certain helicopters removing from service any bolt, washer, and nut installed on the TR hub body at certain life limits and replacing them with airworthy parts and accomplishing further inspections. Additionally, AD 2021-26-07 prohibits the installation of a certain part-numbered TR hub body unless certain requirements are met. Since the FAA issued AD 2021-26- 07, it was determined that modifying the link of the TR hub body and splined flange by adding red paint marks is necessary to enable the detection of any loss of tightening torque. This proposed AD would require the same repetitive inspections and corrective actions as AD 2021-26-07 and would require modification of the link of the TR hub body, which would be a terminating action for the repetitive inspections. The proposed AD would also require repetitive inspections of the red paint line added during the modification of the link of the TR hub body for alignment. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for CFM Engines
The FAA proposes to adopt a new airworthiness directive (AD) for certain CFM International, S.A. (CFM) Model LEAP-1A23, LEAP-1A24, LEAP-1A24E1, LEAP-1A26, LEAP-1A26CJ, LEAP-1A26E1, LEAP-1A29, LEAP- 1A29CJ, LEAP-1A30, LEAP-1A32, LEAP-1A33, LEAP-1A33B2, and LEAP-1A35A engines. This proposed AD was prompted by a report of multiple aborted takeoffs and air turn-backs (ATBs) caused by high-pressure compressor (HPC) stall, which was induced by high levels of non-synchronous vibration (NSV). Additional manufacturer investigation revealed that wear on the No. 3 bearing spring finger housing can lead to high levels of NSV. This proposed AD would require initial and repetitive calculations of the levels of NSV, inspection of the stage 2 high- pressure turbine (HPT) nozzle assembly honeycomb and HPT stator stationary seal honeycomb and, depending on the results of the calculations and inspections, replacement of certain parts. This AD also requires replacement of certain No. 3 bearing spring finger housings at a certain time. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🚁FAA Withdraws Proposed Airworthiness Directive for Safran Engines
The FAA is withdrawing an NPRM that proposed to adopt a new airworthiness directive (AD) that would have applied to all Safran Helicopter Engines, S.A. (Safran) Model ARRIUS 2F and ARRIUS 2R engines. The NPRM was prompted by a manufacturer investigation that revealed certain high-pressure (HP) turbine blades may contain non- compliant porosity rates due to a change in the manufacturing process. The NPRM would have required replacement of affected HP turbine blades. Since the NPRM was issued, further investigation and tests demonstrated that the non-compliant rate of porosity has no impact on the use limit of the affected parts and the FAA has determined that the unsafe condition no longer exists. Accordingly, the NPRM is withdrawn.
Learn More✈️Proposed AD for Boeing 787-9 and 787-10
The FAA proposes to adopt a new airworthiness directive (AD) for certain The Boeing Company Model 787-9 and 787-10 airplanes. This proposed AD was prompted by reports of multiple supplier notices of escapement (NOEs) indicating that multiple cargo barrier fitting links were possibly manufactured with an incorrect titanium alloy material. This proposed AD would require a high frequency eddy current (HFEC) or handheld X-ray fluorescence (XRF) spectrometer inspection of the cargo barrier fitting link to determine the titanium alloy material, and applicable on-condition actions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Requests Comments on Aircraft Security Document Collection
In accordance with the Paperwork Reduction Act of 1995, FAA invites public comments about our intention to request the Office of Management and Budget (OMB) approval to revise and renew an information collection. The collection involves a security holder completing an AC Form 8050-98, Aircraft Security Agreement and returning a completed AC Form 8050-41, Notice of Recordation--Aircraft Security Conveyance with Part II--Release to the Civil Aviation Registry, Aircraft Registration Branch (Registry). The information is used to record a security interest in an aircraft and eligible engines, propellers, or spare part locations and release that interest when the debt is satisfied.
Learn More🚁Airworthiness Directive for Bell Textron Helicopters - FAA Compliance
The FAA is adopting a new airworthiness directive (AD) for all Bell Textron Canada Limited (BTCL) Model 407 and 427 helicopters. This AD was prompted by a report that certain expandable blade bolts installed on the main rotor blade may not have received the correct heat treatment, which could result in stress corrosion cracking of the expandable blade bolts. This AD requires removing the expandable blade bolts from service and replacing them with a part eligible for installation. This AD also prohibits the installation of an affected expandable blade bolt on any helicopter. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directives for Airbus SAS Airplanes
The FAA proposes to supersede Airworthiness Directive (AD) 2024-08-05, which applies to certain Airbus SAS Model A330-200 series, A330-200 Freighter series, A330-300 series, A330-841, and A330-941 airplanes. AD 2024-08-05 requires revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive airworthiness limitations. Since the FAA issued AD 2024-08- 05, the FAA has determined that additional new and more restrictive airworthiness limitations are necessary. This proposed AD would retain certain actions in AD 2024-08-05 until the existing maintenance or inspection program, as applicable, is revised to incorporate the new and more restrictive airworthiness limitations. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for De Havilland Aircraft Compliance
The FAA proposes to supersede Airworthiness Directive (AD) 2019-16-09, which applies to certain De Havilland Aircraft of Canada Limited Model DHC-8-400 series airplanes. AD 2019-16-09 requires one- time inspections for cracks and damage of the elevator power control unit (PCU) brackets and surrounding area, horizontal stabilizer rear spar, and elevator front spar, and related investigative and corrective actions if necessary. Since the FAA issued AD 2019-16-09, new findings have been reported as a result of maintenance activities and/or inspections. This proposed AD would continue to require certain actions in AD 2019-16-09, and would also require repeating the inspections one time and performing applicable on-condition actions, remove an airplane from the applicability, and provide optional terminating action for the repetitive inspections. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for PZL M28-05 Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all Polskie Zaklady Lotnicze Sp. z o.o. Model PZL M28 05 airplanes. This proposed AD was prompted by incorrect flap settings and airspeed during approach for landing under one engine inoperative (OEI) conditions in the airplane flight manual (AFM) emergency procedures. This proposed AD would require revising the existing AFM for your airplane to provide the correct emergency procedures. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More🚁New Airworthiness Directive for Airbus AS332L1 Helicopters
The FAA is adopting a new airworthiness directive (AD) for all Airbus Helicopters Model AS332L1 helicopters. This AD was prompted by a determination that new or more restrictive airworthiness limitations are necessary. This AD requires revising the airworthiness limitations section (ALS) of the existing maintenance manual (MM) or instructions for continued airworthiness (ICAs) and the existing approved maintenance or inspection program, as applicable. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More