✈️New Airworthiness Directives for GE Engines by FAA
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, and GEnx-2B67/P engines. This AD was prompted by a manufacturer's investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This AD requires replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Airbus Canada's BD-500 Airplanes
The FAA is superseding Airworthiness Directive (AD) 2022-19- 09, which applied to all Airbus Canada Limited Partnership Model BD- 500-1A10 and BD-500-1A11 airplanes. AD 2022-19-09 required repetitive inspections of the left and right main landing gear (MLG) lower spindle pins to detect corrosion and applicable repair or replacement. This AD was prompted by reports of in-service findings of corrosion on the flange of the MLG lower spindle pin. This AD continues to require certain actions in AD 2022-19-09. This AD also requires changing the tracking of flight cycles for inspections from the usage of the MLG to the usage of MLG lower spindle assemblies and replacement of affected MLG lower spindle assemblies, removes airplanes from the applicability, and prohibits the installation of affected parts under certain conditions; as specified in a Transport Canada AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Boeing Airplanes Addresses Elevator Safety
The FAA is adopting a new airworthiness directive (AD) for all The Boeing Company Model DC-9-81 (MD-81), DC-9-82 (MD-82), DC-9-83 (MD- 83), DC 9-87 (MD-87), and MD-88 airplanes, and Model DC-9-10, DC-9-20, DC-9-30, DC-9-40, and DC-9-50 series airplanes. This AD was prompted by the discovery of jammed elevators during takeoff. This AD requires revising the "Certificate Limitations" section of the existing airplane flight manual (AFM) to include a procedure to confirm elevator surfaces are not jammed in the trailing edge down (TED) position. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for Bombardier Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for certain Bombardier, Inc., Model CL-600-1A11 (600), CL-600-2A12 (601), and CL-600-2B16 (601-3A, 601-3R, and 604 Variants) airplanes. This proposed AD was prompted by tail strikes that occurred during landing with partial flap configurations. This proposed AD would require revising the existing airplane flight manual (AFM) to provide the flightcrew with procedures to follow when landing under certain conditions. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Issues Airworthiness Directive for Thommen Aircraft Equipment
The FAA is correcting an airworthiness directive (AD) that published in the Federal Register. The AD applies to certain Thommen Aircraft Equipment AG (THOMMEN) AC32 Digital Air Data Computers (ADCs). As published, there were typographical errors in the some of the aircraft models in the applicability table. This document corrects those errors. In all other respects, the original document remains the same.
Learn More✈️Proposed Airworthiness Directive for CFM International Engines
The FAA proposes to supersede Airworthiness Directive (AD) 2023-23-12, which applies to all CFM International, S.A. (CFM) Model LEAP-1B21, LEAP-1B23, LEAP-1B25, LEAP-1B27, LEAP-1B28, LEAP-1B28B1, LEAP-1B28B2, LEAP-1B28B2C, LEAP-1B28B3, LEAP-1B28BBJ1, and LEAP- 1B28BBJ2 (LEAP-1B) engines. AD 2023-23-12 requires replacing certain high-pressure turbine (HPT) rotor stage 1 disks and a certain compressor rotor stages 6-10 spool. Since the FAA issued AD 2023-23-12, the manufacturer has identified additional parts that were manufactured from material suspected to have reduced material properties due to iron inclusion, which prompted this proposed AD. This proposed AD would retain the requirements to replace certain HPT rotor stage 1 disks and a certain compressor rotor stages 6-10 spool. This proposed AD would also expand the applicability to include additional affected HPT rotor stage 1 disks that were manufactured from the same material suspected to have reduced material properties due to iron inclusion. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed FAA Airworthiness Directive for MHI RJ Aviation Aircraft
The FAA proposes to adopt a new airworthiness directive (AD) for all MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), Model CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000). This proposed AD was prompted by an engine indicating and crew alerting system (EICAS) STAB TRIM Caution message that was posted, and subsequent repair that found prematurely worn teeth on a rubber bull gear (RBG) wheel in the horizontal stabilizer trim actuator (HSTA). This proposed AD would require an inspection for part numbers and on-condition replacement of affected RBG wheels and prohibit the installation of affected parts under certain conditions, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️Proposed Airworthiness Directive for MHI RJ Aviation Aircraft
The FAA proposes to adopt a new airworthiness directive (AD) for all MHI RJ Aviation ULC Model CL-600-2C10 (Regional Jet Series 700, 701, and 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was prompted by a determination that new or more restrictive aircraft maintenance manual (AMM) tasks are necessary. This proposed AD would require revising the existing maintenance or inspection program, as applicable, to incorporate new or more restrictive AMM tasks, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directive for MHI RJ Aviation Airplanes
The FAA proposes to adopt a new airworthiness directive (AD) for all MHI RJ Aviation ULC (type certificate previously held by Bombardier, Inc.) Model CL-600-2C10 (Regional Jet Series 700, 701 & 702), CL-600-2C11 (Regional Jet Series 550), CL-600-2D15 (Regional Jet Series 705), CL-600-2D24 (Regional Jet Series 900), and CL-600-2E25 (Regional Jet Series 1000) airplanes. This proposed AD was prompted by reports that the cockpit voice recorder (CVR) impact switch was installed in the wrong direction. This proposed AD would require an inspection of the CVR impact switch installation to confirm that the reset switch faces forward, and applicable on-condition actions, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Proposes Airworthiness Directive for Airbus Duct Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for certain Airbus Canada Limited Partnership Model BD-500-1A10 and BD- 500-1A11 airplanes. This proposed AD was prompted by certification testing that found that environmental control system (ECS) ducts manufactured using a certain material failed the flammability test requirements established for compliance. This proposed AD would require inspecting the affected ECS ducts and, as applicable, installing a fire-resistant sleeve assembly over any non-compliant ECS duct, and prohibit the installation of ECS ducts as replacement parts under certain conditions, as specified in a Transport Canada AD, which is proposed for incorporation by reference (IBR). The FAA is proposing this AD to address the unsafe condition on these products.
Learn More