🚁FAA Issues Airworthiness Directive for Robinson Helicopter Inspections
The FAA is superseding Airworthiness Directive (AD) 2024-19-11 for all Robinson Helicopter Company Model R44 and R44 II helicopters. AD 2024-19-11 required visually inspecting a certain flex plate assembly (flex plate) and certain clutch shaft forward yokes (yokes), including each flex plate bolt, and depending on the results, taking corrective actions. AD 2024-19-11 also required removing certain yokes from service within a specified threshold, or as an alternative, performing in-depth inspections. Since the FAA issued AD 2024-19-11, it has been determined that clarifications regarding the alternative inspections are necessary. This AD requires the actions of AD 2024-19- 11 and clarifies that the alternative inspections are repetitive and adds a particular paint remover option to use when performing those alternative inspections. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️Analysis of Pratt & Whitney Airworthiness Directive Compliance
The FAA proposes to adopt a new airworthiness directive (AD) for certain Pratt & Whitney Division (PW) Model PW4074, PW4074D, PW4077, PW4077D, PW4084D, PW4090, and PW4090-3 engines. This proposed AD was prompted by an analysis of an event involving an International Aero Engines, LLC (IAE LLC) Model PW1127GA-JM engine, which experienced a high-pressure compressor (HPC) 7th-stage integrally bladed rotor (IBR-7) separation that resulted in an aborted takeoff. This proposed AD would require repetitive angle ultrasonic scan inspections (AUSIs) of the HPC 15th-stage disks, front turbine hubs, high pressure turbine (HPT) 1st-stage air seals, and HPT 2nd-stage hubs for crack indications, and removal from service and replacement if necessary, and for certain serial numbers, removal from service and replacement of the HPT 1st-stage air seal. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive Update for Boeing 787 Series Aircraft
The FAA is correcting an airworthiness directive (AD) that was published in the Federal Register. The AD applies to certain The Boeing Company Model 787-9 and 787-10 airplanes. As published, a reference to the Alternative Methods of Compliance (AMOCs) paragraph in the regulatory text is incorrect. This document corrects that error. In all other respects, the original document remains the same.
Learn More✈️New Airworthiness Directive for Textron Aviation Fire Safety Measures
The FAA is adopting a new airworthiness directive (AD) for certain Textron Aviation, Inc., Model 560 and 560XL airplanes. This AD was prompted by reports of mis-wired fire extinguishing bottles. This AD requires an engine fire extinguisher system functional test, an inspection of the fire extinguisher bottle cartridge wire numbers and yellow ID sleeves for proper identification and legibility, and applicable corrective actions. This AD also requires revising the existing inspection program to incorporate new airworthiness limitations for repetitive inspections of the engine fire extinguisher wiring and, as applicable, auxiliary power unit (APU) fire extinguisher wiring. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️FAA Airworthiness Directive for Airbus A350-941
The FAA is adopting a new airworthiness directive (AD) for all Airbus SAS Model A350-941 airplanes. This AD was prompted by an inspection that found several anodic burns on the main landing gear (MLG) bogie beam axles following a high velocity oxygen-fuel (HVOF) stripping process. This AD requires replacement of affected MLG bogie beam axles and prohibits the installation of affected parts. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directives for GE Engines by FAA
The FAA is adopting a new airworthiness directive (AD) for certain General Electric Company (GE) Model GEnx-1B64, GEnx-1B64/P1, GEnx-1B64/P2, GEnx-1B67, GEnx-1B67/P1, GEnx-1B67/P2, GEnx-1B70, GEnx- 1B70/75/P1, GEnx-1B70/75/P2, GEnx-1B70/P1, GEnx-1B70/P2, GEnx-1B70C/P1, GEnx-1B70C/P2, GEnx-1B74/75/P1, GEnx-1B74/75/P2, GEnx-1B76/P2, GEnx- 1B76A/P2, and GEnx-2B67/P engines. This AD was prompted by a manufacturer's investigation that revealed certain high-pressure turbine (HPT) stage 1 and HPT stage 2 disks were manufactured from powder metal material suspected to contain iron inclusion. This AD requires replacement of affected HPT stage 1 and HPT stage 2 disks with parts eligible for installation. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More🛩️New Airworthiness Directive for Airbus Helicopters EC225LP
The FAA is adopting a new airworthiness directive (AD) for certain Airbus Helicopters Model EC225LP helicopters. This AD was prompted by the identification of missing electrical bonding on a certain part-numbered additional and optional search light (search light). This AD requires installing an electrical bonding braid modification. These actions are specified in a European Union Aviation Safety Agency (EASA) AD, which is incorporated by reference. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Boeing 787 Impacts Compliance Costs
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 787-8, 787-9, and 787-10 airplanes. This AD was prompted by reports of multiple supplier notices of escapement (NOEs) indicating that seat track splice fittings were possibly manufactured with an incorrect titanium alloy material. This AD requires an inspection of seat track splice fittings to determine the material and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More✈️New Airworthiness Directive for Boeing 757-200/-300 Series Airplanes
The FAA is adopting a new airworthiness directive (AD) for certain The Boeing Company Model 757-200, -200CB, and -300 series airplanes. This AD was prompted by a report of cracking found in new locations at a certain body station (STA) during frame segment replacement repairs, including in the web at the K-hole between certain stringers, in the outer chord above the lower hinge intercostal, and in the inner chord and web between certain stringers. This AD requires an inspection or records check for the presence of approved or local repairs, repetitive eddy current inspections for cracking, and applicable on-condition actions. The FAA is issuing this AD to address the unsafe condition on these products.
Learn More🚁Proposed Airworthiness Directive for Airbus Helicopters AD 2025-0916
The FAA proposes to supersede Airworthiness Directive (AD) 2024-10-13, which applies to all Airbus Helicopters Model AS332C, AS332C1, AS332L, AS 332L1, AS 332L2, and EC 225LP helicopters. AD 2024- 10-13 requires visually inspecting the bowls of the left-hand (LH) and right-hand (RH) fuel filters for any cracks and seepage. Depending on the inspection results, AD 2024-10-13 requires removing an affected fuel filter from service and replacing that part. AD 2024-10-13 also allows a certain fuel filter to be installed on any helicopter if certain actions are accomplished. Since the FAA issued AD 2024-10-13, additional inspection criteria was developed. This proposed AD would require the same actions as AD 2024-10-13 but would remove some helicopters from the applicability, add an inspection of the inner surface of the fuel filter bowls, and revise the tightening torque. The FAA is proposing this AD to address the unsafe condition on these products.
Learn More